Home / Blog / Air and VOCs

AIR AND VOCs

Catalytic removal of ethylene oxide from sterilization emissions

Ethylene oxide is toxic even at very low concentrations and easily forms flammable mixtures. At a sterilization facility, air treatment is what keeps the pollutant from leaving the plant.

W
WIZZUM engineering teamPublished on 12/09/2025 · Updated on 16/11/2026 · 5 min read

CONTENTS

IN SHORT

  • EtO emissions are highly variable: short, high peaks from the vacuum pumps and a steady, lower flow from the aeration chambers.
  • A two-stage system works: a water column evens out the concentrations and a catalytic reactor oxidizes the EtO to CO₂ and water with an efficiency above 99%.
  • The method produces no secondary liquid waste, and negative pressure and LEL monitoring reduce the risk.

Why ethylene oxide requires special control

Ethylene oxide (EtO) is widely used to sterilize medical devices that cannot withstand high temperature or humidity. It is toxic even at very low concentrations and, within a certain range, forms a flammable mixture with air. Ventilating or diluting is not enough.

That is why, here, the air treatment installation is not an add-on to the process. It is the decisive safety barrier between the industrial process and the plant’s surroundings.

The problem: emissions that change constantly

The amount of EtO in the exhaust gases fluctuates widely during degassing and aeration. The vacuum pump discharge produces short, high peaks, while the aeration chambers emit smaller amounts, but continuously.

If that stream goes straight to the catalytic reactor, without dampening, the result is thermal shocks, incomplete conversion and operation close to the lower explosive limit (LEL).

The requirements are strict. In the United States, a destruction efficiency above 99% and an outlet concentration below 1 ppm are expected, although the stricter rules the EPA approved in 2024 are under review. In Germany, TA Luft treats ethylene oxide as a carcinogen and requires very low concentrations in the exhaust gases. With these targets, absorption systems on their own or uncontrolled thermal oxidation do not work in practice.

The two-stage solution

Stage 1: evening out the concentrations

A water column with recirculation absorbs EtO during peaks and releases it when the concentration drops. This stage does not remove the ethylene oxide; it only stabilizes the stream going to the next one. Peak loads are reduced, there are fewer occasions of approaching the LEL and the reactor temperature is more stable.

Stage 2: catalytic oxidation

In the reactor, the EtO is oxidized to CO₂ and water. The reaction is exothermic, so a heat exchanger recovers part of the energy and reduces fuel consumption. Preheating at the inlet (gas, electric or steam) keeps the catalyst within its optimum temperature range.

There is one condition: the gas may only contain compounds of carbon, hydrogen, nitrogen and oxygen, with no catalyst poisons. Under those conditions, efficiency exceeds 99%. We explain when a catalyst is not a good idea in the comparison of RTO, RCO and biofilters.

No secondary waste

Some scrubbers that work with sulfuric acid or glycol produce a liquid effluent that then has to be managed. Catalytic oxidation converts EtO into stable gaseous products without additional reagents. That means simpler regulatory compliance, less handling of chemicals and no fixed disposal costs.

Negative pressure and tightness

An extraction fan placed after the reactor keeps the whole installation under slight negative pressure, which limits fugitive emissions. The next layers of protection are integrated LEL measurement and automatic temperature control.

Treatment as part of the sterilization cycle

The treatment installation has to be designed together with the whole process:

  • preconditioning;
  • sterilization;
  • vacuum degassing;
  • aeration in quarantine;
  • final air treatment.

The system has to handle both the high peaks from degassing and the steady, lower load from aeration.

What to assess before implementing it

  • the EtO mass balance;
  • a map of how concentrations vary over the cycle;
  • hazard identification;
  • the presence of catalyst poisons in the gases;
  • the variability of the production cycles;
  • fuel availability for preheating;
  • the options for energy integration: operating under steady conditions clearly reduces the need for auxiliary fuel.

Whether the solution is viable, and what it costs, depends on this data.

Conclusion

Evening out the concentrations hydraulically and combining this with catalytic oxidation makes it possible to meet strict emission limits without secondary waste. But efficiency does not depend only on the reactor and the catalyst: process stabilization, heat management, tightness and good integration with the sterilization stages also count.

Frequently asked questions

What efficiency does catalytic oxidation of ethylene oxide achieve?+

More than 99%, if the gas only contains compounds of carbon, hydrogen, nitrogen and oxygen and carries no catalyst poisons.

What is the water column ahead of the catalytic reactor for?+

It absorbs EtO during peaks and releases it when the concentration drops. It does not remove the pollutant, but it evens out the stream, so the reactor does not suffer thermal shocks and the installation operates well away from the lower explosive limit.

Does this method produce wastewater?+

No. Unlike some scrubbers using sulfuric acid or glycol, catalytic oxidation produces no liquid waste: the EtO is converted into CO₂ and water.

W

AUTHOR

WIZZUM engineering team

We design and commission wastewater and gas treatment installations for industry, from benchmarking and FEED engineering to start-up.

NEED HELP?

Are you planning gas treatment for ethylene oxide?

  • Comparative technical analyses
  • Design and delivery of turnkey installations
  • Environmental benchmarking and BAT analysis

Environmental engineering for industry.
Industrial wastewater, emissions and odors.

OFFICE

Avda. Cabrera, 36
08302 Mataró (Barcelona), Spain
info@wizzum.com

© 2026 Wizzum. All rights reserved.