Home / Technologies

Technologies

Industrial gas and wastewater treatment technologies

An overview of the technologies we compare when choosing the solution for an air emission or an industrial wastewater. For each one we list its typical applications and operating ranges.

8 technologies

VOCs and solvents

1234

1 Combustion chamber with burner2 Ceramic beds3 Fan4 Stack

Regenerative thermal oxidizer (RTO)

Oxidizes VOCs at high temperature; the heat of the cleaned gas is stored in ceramic beds and passed to the incoming gas. Also called a regenerative incinerator.

Applications

Chemicals and petrochemicals, pharmaceuticals, paints and coatings, food, waste and biogas, printing

Technical data

Flow rate
1,000–250,000 Nm³/h
VOC concentration
Low to medium; autothermal from 1.5 g/Nm³
Efficiency
> 99 %
Temperature
750–1300 °C
Technical details →
1234

1 Electric heating elements2 Ceramic beds3 Power supply4 Stack

Electric RTO (e-RTO)

An RTO heated by electric elements instead of a burner: no flame, no combustion NOx and, with renewable power, no CO₂ emissions. Also called an electric incinerator.

Applications

Chemicals, coatings, flexographic printing, odor abatement

Technical data

Flow rate
5,000–100,000 Nm³/h
VOC concentration
Low, medium or high
Efficiency
> 99 %
Temperature
Around 850 °C; up to 1100 °C
Technical details →
1234

1 Heat exchanger2 Preheater3 Catalyst bed4 Stack

Catalytic oxidation

Oxidizes VOCs over a catalyst bed, at a much lower temperature than thermal oxidation.

Applications

Pharmaceuticals, fine chemicals, printing, plastics, paints and varnishes, wood industry, food

Technical data

Flow rate
1,000–30,000 Nm³/h
VOC concentration
0.1–10 g/Nm³
Efficiency
> 95 %
Temperature
250–450 °C
Technical details →
1234

1 Burner2 Combustion chamber3 Recuperator4 Stack

Recuperative thermal oxidation

Thermal oxidation with a recuperator that produces steam, hot water or thermal oil, or preheats the incoming air. Also called an incinerator with recuperator.

Applications

Chemicals, paints and coatings, printing and packaging, pharmaceuticals, waste treatment

Technical data

Flow rate
1,000–10,000 Nm³/h
VOC concentration
High; autothermal from 3–5 g/Nm³
Efficiency
> 99 %
Temperature
750–950 °C; up to 1200 °C
Technical details →
123

1 Burner2 Combustion chamber3 Stack

Direct thermal oxidation

Controlled combustion with excess oxygen and no prior concentration, for heavily loaded gas streams. The simplest kind of thermal incinerator.

Applications

Chemicals, pharmaceuticals, petrochemicals, waste, industrial coatings

Technical data

Flow rate
500–50,000 Nm³/h
VOC concentration
High, with support fuel
Efficiency
> 99 %
Temperature
750–950 °C
Technical details →
1234

1 Prefilter2 Zeolite rotor3 Oxidizer4 Stack

Zeolite concentrator

An adsorption and desorption rotor cuts the gas volume by up to 16 times before it goes to oxidation.

Applications

Large flow rates with very dilute VOCs

Technical data

Flow rate
10,000–200,000 Nm³/h
VOC concentration
< 1 g/Nm³
Efficiency
90–98% in the rotor
Temperature
Desorption at 180–220 °C
Technical details →
1234

1 Absorption column2 Desorption column3 Condenser4 Solvent tank

Solvent scrubber

Selective absorption or reaction with amines for halogenated compounds, aldehydes and hydrocarbons that other scrubbers don't remove.

Applications

Chemicals, petrochemicals, fumigation, fibers and viscose

Technical data

Flow rate
1,000–60,000 m³/h
VOC concentration
C1 halogenated compounds, aldehydes, CS₂
Efficiency
90–99% depending on solubility
Temperature
Gas below 40 °C
Technical details →
1234

1 Activated carbon bed2 Standby adsorber3 Fan4 Stack

Activated carbon adsorption

Retains VOCs on activated carbon; if it is regenerated with steam or inert gas, the solvent can be recovered.

Applications

Wastewater treatment plants, food, chemicals and pharmaceuticals, biogas, solar thermal power plants

Technical data

Flow rate
1,000–100,000 Nm³/h
VOC concentration
Low
Efficiency
90–99 %
Temperature
Below 40–50 °C
Technical details →

Comparison: VOCs and solvents

Typical operating ranges of the technologies in this group. The values for each installation depend on the composition of the gas or the wastewater.

TechnologyFlow rateVOC concentrationEfficiencyTemperature
Regenerative thermal oxidizer (RTO)1,000–250,000 Nm³/hLow to medium; autothermal from 1.5 g/Nm³> 99 %750–1300 °C
Electric RTO (e-RTO)5,000–100,000 Nm³/hLow, medium or high> 99 %Around 850 °C; up to 1100 °C
Catalytic oxidation1,000–30,000 Nm³/h0.1–10 g/Nm³> 95 %250–450 °C
Recuperative thermal oxidation1,000–10,000 Nm³/hHigh; autothermal from 3–5 g/Nm³> 99 %750–950 °C; up to 1200 °C
Direct thermal oxidation500–50,000 Nm³/hHigh, with support fuel> 99 %750–950 °C
Zeolite concentrator10,000–200,000 Nm³/h< 1 g/Nm³90–98% in the rotorDesorption at 180–220 °C
Solvent scrubber1,000–60,000 m³/hC1 halogenated compounds, aldehydes, CS₂90–99% depending on solubilityGas below 40 °C
Activated carbon adsorption1,000–100,000 Nm³/hLow90–99 %Below 40–50 °C

Datasheet

Do you need the full datasheet for a technology?

Tell us your flow rate and what you emit or discharge, and we'll tell you which technology fits your plant.

Datasheet

Request the full datasheet

Choose the technology and leave us your details. An engineer who knows that technology will send you the datasheet.

  • Full technical data for the technology you choose
  • An assessment of whether it suits your gas or your effluent

Would you rather write to us directly?

info@wizzum.com

The first conversation is free and with no obligation.