Home / Blog / ZLD and water recovery

ZLD AND WATER RECOVERY

Compact plants: containerized drinking water, desalination and water reuse

Factory-assembled and tested installations, on a skid or in a container, to produce drinking water, desalinate or reuse water. Capacities, applications and installation requirements.

W
WIZZUM engineering teamPublished on 16/06/2026 · 5 min read

CONTENTS

IN SHORT

  • A compact plant arrives factory-assembled and tested, and is connected on site in a few days.
  • It has three main uses: producing drinking water, desalinating seawater or brackish water, and reusing treated wastewater.
  • For very large flow rates, an installation built on site is still cheaper.

Not every water treatment installation needs civil works and months of installation. For small and medium flow rates, a compact plant arrives factory-assembled and tested, on a skid or in a container, and is connected on site in a few days. It is the typical solution for remote sites, temporary supply and plants that want to treat water without building a treatment plant.

What a compact plant is

All the equipment (pumps, filters, membranes, dosing, electrical panel and controls) is mounted on a stainless steel frame or inside a 20 or 40 ft container. Factory acceptance tests (FAT) are carried out with the equipment connected before shipping. On site, all that is needed is to prepare the ground, connect water and power and start up the plant.

It has three main uses.

Drinking water treatment

It turns well, river, aquifer or mains water into water fit for drinking. The treatment line depends on the raw water analysis: prefiltration, coagulation, filtration, adsorption, membranes, reverse osmosis and disinfection, combined as needed. See the compact drinking water plant datasheet.

123

1 Sand and carbon filters 2 UV lamp 3 Pump

Container with filters, UV lamp and pump, factory-assembled and tested.
  • Capacity from 20 to 2,500 m³/day, expandable with modules in parallel
  • Recovery from 70%
  • Lead time of around 8–14 weeks
  • Designed to meet the requirements for water intended for human consumption (Directive (EU) 2020/2184 and national regulations)

Desalination

It produces fresh water from seawater or brackish water by reverse osmosis. With seawater it runs at 60–70 bar and recovers around 45% of the inlet water; with brackish water the pressure is lower and the recovery higher. Energy recovery devices bring consumption down to around 2.25 kWh/m³ with seawater. More information in the compact desalination plant datasheet.

Capacities from 20 to 2,500 m³/day. For human consumption, the water needs remineralization, disinfection and the corresponding health checks. The brine also needs an outlet.

Water reuse

It treats effluent from a wastewater treatment plant or graywater for non-potable uses: irrigation, cleaning surfaces and machinery, toilet flushing or process water. It combines filtration, ultrafiltration, reverse osmosis, activated carbon and disinfection, depending on the inlet water and the intended use. It can cut mains water consumption by up to 70%. See the compact water reuse plant datasheet.

The required quality and the scope of monitoring depend on the use and are set before sizing, in line with the applicable regulations, including Regulation (EU) 2020/741 when the water is used for agricultural irrigation. Reclaimed water is never fit for drinking.

When a compact plant makes sense

  • Remote or off-grid sites: mines, construction sites, isolated facilities.
  • Temporary or emergency supply, because the plant can be relocated.
  • Industrial plants that need process water or want to reuse their wastewater without civil works.
  • Hotels, ports and residential developments that want to reduce their water consumption.
  • Fast expansions of an existing installation.

Advantages and limitations

For: short lead time, controlled assembly in the factory, little civil work, remote monitoring and the option to relocate.

Against: for very large flow rates, an installation built on site is still cheaper, and the treatment line has to be well defined from the start, because there is little room in a container.

What you need to order one

  • A full analysis of the inlet water
  • The intended use and the required quality
  • The daily flow rate and operating hours
  • The available space, access and utility connections
  • Where the concentrate or brine will go

With this data, the treatment line and the format are defined: on a skid or in a container. If the water is for boilers or for the process, you may find the article on whether to soften or demineralize useful.

Frequently asked questions

How long does it take to deliver a compact plant?+

Roughly 8 to 14 weeks, depending on the treatment line and the equipment.

Can reclaimed water be used for drinking?+

No. Reclaimed water is for non-potable uses, such as irrigation, cleaning or the process.

What flow rates are compact plants used for?+

Usually 20 to 2,500 m³/day, expandable with more modules.

W

AUTHOR

WIZZUM engineering team

We design and commission wastewater and gas treatment installations for industry, from benchmarking and FEED engineering to start-up.

NEED HELP?

Do you need water at a specific site?

  • Comparative technical analyses
  • Design and delivery of turnkey installations
  • Environmental benchmarking and BAT analysis

Environmental engineering for industry.
Industrial wastewater, emissions and odors.

OFFICE

Avda. Cabrera, 36
08302 Mataró (Barcelona), Spain
info@wizzum.com

© 2026 Wizzum. All rights reserved.