Home / Blog / Air and VOCs

AIR AND VOCs

Ceramics: emissions from kilns, dryers and spray dryers

Dust, fluorides, sulfur oxides and VOCs: what each stage of a ceramics plant emits and which technologies are used to treat it.

W
WIZZUM engineering teamPublished on 10/03/2026 · 5 min read

CONTENTS

IN SHORT

  • A ceramics plant has several sources with very different profiles. Each one has to be measured separately.
  • In raw material preparation and spray dryers, the main problem is dust: cyclones and bag filters and, if the gas is humid, wet scrubbers.
  • Kilns add fluorides and acid gases; a common solution is dry sorbent injection with a bag filter.

A ceramics plant has several emission sources with very different profiles. Raw material preparation and spray dryers mainly emit dust. Firing kilns emit hot gases that may contain fluorides, chlorides, sulfur oxides and, with some products, organic compounds. To treat each source properly, start by measuring it separately.

Raw material preparation and milling

Mills, conveyor belts, silos and screens produce dust from clay and other raw materials. It is a dry, fine mineral dust. The typical solution is local extraction with a bag filter or cartridge filter. The collected dust can be returned to the process.

Spray dryers

Spray dryers dry the slip with hot gases and produce the spray-dried powder for pressing. Their emission has a large flow rate, high temperature and humidity and a heavy load of fine dust. The most common setup is:

  • Cyclones as a first stage, which recover most of the dust.
  • A bag filter after them, with bags suited to the temperature and operated so that the gas does not reach its dew point inside the filter.
  • Wet scrubbers or Venturi scrubbers when the humidity of the gas makes dry filtration difficult. They produce water with suspended solids that, at many plants, can be returned to slip preparation.
1234

1 Filter bags 2 Pulse cleaning 3 Dust hoppers 4 Fan

The dust stays on the bags, and compressed air pulses knock it into the hoppers.

Dryers

Dryers for pieces mainly emit water vapor and some dust. They are usually the simplest sources, but it is worth measuring them to rule out organic compounds from additives.

Kilns

This is the source with the widest range of pollutants:

  • Dust from the pieces and from the process itself.
  • Fluorides (HF), which some clays release at high temperature.
  • Chlorides (HCl) and sulfur oxides, depending on the raw materials and the fuel.
  • Organic compounds from additives, binders or inks in some products.

For fluorides and acid gases with dust, dry treatment is widely used: an alkaline sorbent, such as calcium hydroxide, is injected into the duct, followed by a bag filter that captures both the dust and the reacted sorbent. Another option is wet scrubbers with an alkaline solution (alkaline scrubber), which capture acid gases very well but produce a bleed that has to be treated.

If there are organic compounds or odors, thermal oxidation is considered, which can use part of the heat from the kiln itself.

What makes treatment harder

Temperature. Kiln gases leave hot and have to be cooled before the bag filter, but without dropping below the acid dew point, where acids condense and cause corrosion.

Large flow rates. Kilns and spray dryers move a lot of air. Any treatment that requires heating or cooling it has a significant energy cost.

Production changes. A change of product, glaze or raw material changes the emission. That is why it is worth measuring with the most demanding products.

Combining sources. Joining several sources into one installation reduces the investment, but may force you to treat all the air because of a pollutant that only one of them carries.

How to approach it

  1. Source inventory: which stage goes to which stack and at what flow rate.
  2. Measurement of each source: dust, fluorides, chlorides, sulfur oxides, TOC, temperature and humidity.
  3. Comparison with the permit limits and with the emission levels associated with the best available techniques for the sector. We explain where to start the BAT analysis in the article on BAT conclusions.
  4. Choice of treatment for each source, taking dust and heat recovery into account.

Frequently asked questions

How are fluorides removed from ceramic kiln gases?+

The most common approach is to inject an alkaline sorbent, such as calcium hydroxide, in dry form and filter with a bag filter. The alternative is a wet scrubber with an alkaline solution.

Why can't the gases reach the bag filter too cold?+

Below the acid dew point, acids condense in the filter, corrode the equipment and clog the bags.

Can the captured dust be returned to production?+

Often yes, especially dust from raw material preparation and from the spray dryers.

W

AUTHOR

WIZZUM engineering team

We design and commission wastewater and gas treatment installations for industry, from benchmarking and FEED engineering to start-up.

NEED HELP?

Do you have a ceramics plant with several emission sources?

  • Comparative technical analyses
  • Design and delivery of turnkey installations
  • Environmental benchmarking and BAT analysis

Environmental engineering for industry.
Industrial wastewater, emissions and odors.

OFFICE

Avda. Cabrera, 36
08302 Mataró (Barcelona), Spain
info@wizzum.com

© 2026 Wizzum. All rights reserved.