Home / Blog / Air and VOCs

AIR AND VOCs

e-RTO: oxidizing VOCs without a flame and without natural gas

An RTO heated by electric heating elements instead of a burner. How it works, when it uses electricity and when it doesn’t, and what to check at the plant before choosing it.

W
WIZZUM engineering teamPublished on 17/09/2024 · 5 min read

CONTENTS

IN SHORT

  • The e-RTO has the same towers, beds and valves as a classic RTO. Only the heat source changes: heating elements instead of a burner.
  • Above the autothermal point, the heating elements switch off and heating power consumption drops to zero.
  • The deciding factor is the available electrical power, because start-up requires the full power of the heating elements.

A classic RTO uses a gas burner at start-up and when the VOC concentration is not enough to hold the temperature. The e-RTO does the same with electric heating elements mounted in the oxidation chamber. The towers, ceramic beds and valves are the same. The heat source changes and, with it, the unit’s own emissions.

How it works

The VOC-laden gas enters through one tower, heats up in the ceramic bed and reaches the oxidation chamber. Instead of a flame, there is a set of heating elements there that holds the operating temperature, usually around 850 °C and, depending on the design, up to 1100 °C. The VOCs are oxidized to CO₂ and water, and the clean gas gives off its heat to the bed in the second tower before leaving. The valves reverse the flow direction every cycle.

1234

1 Electric heating elements 2 Ceramic beds 3 Power supply 4 Stack

Thyristor-controlled heating elements heat the oxidation chamber; the rest of the process is as in a classic RTO.

When it uses electricity

The e-RTO’s energy use depends on the emission, just like the gas consumption of a classic RTO:

  • At start-up, the heating elements run at 100% until the chamber reaches temperature.
  • Above the autothermal point, the heat comes from the VOCs themselves and the heating elements switch off. Only the fan and the controls use electricity.
  • Below the autothermal point, thyristors control the power of the heating elements to hold the required temperature.

A plant whose average concentration is above that point will pay very little for heating. A plant with a very dilute emission will use energy continuously, just as it would use gas.

What the plant gains

  • No flame, so no combustion NOx forms
  • Less CO₂: zero from heating if the electricity is renewable
  • No gas connection, gas train or combustion air fan
  • Less noise around the unit
  • Simpler installation and commissioning
  • The same removal efficiency as a burner-fired RTO: over 99%

For plants with Scope 1 emission reduction targets or that already have their own photovoltaics, it is a simple way to remove a gas consumer.

What to check before choosing it

Available electrical power. This is the key point. Start-up requires the full power of the heating elements and, with a dilute emission, continuous operation also uses a fair amount of energy. The contracted power, the transformer and the main switchboard have to be checked.

The real average concentration. The longer the e-RTO runs above the autothermal point, the less the electricity price matters. Without measuring over a full production cycle, it cannot be estimated properly.

Electricity price versus gas price. With a dilute emission, which almost always needs heat input, the cost comparison depends on the plant’s tariffs. With on-site photovoltaics, the numbers tip in favor of the e-RTO during sunny hours.

Shutdowns and start-ups. If the line stops every night, each start-up uses energy to reheat the chamber. It is worth calculating whether keeping the unit on hot standby works out better.

What about existing RTOs?

In some cases, the burner of an operating RTO can be replaced with a set of heating elements. It depends on the chamber design, the space and the available power. It is worth considering when the burner reaches the end of its service life or the plant has an electrification plan.

e-RTO versus gas-fired RTO

Burner-fired RTOe-RTO
Heat sourceNatural gas, LPG, biogas or hydrogenElectric heating elements
NOx from heatingYes, from combustionNo
CO₂ from heatingYesZero with renewable electricity
InstallationGas connection and gas trainHigh-power electrical connection
Removal efficiency> 99 %> 99 %
Consumption above the autothermal pointAlmost zeroZero

Essentially it is the same unit with a different heat source. The choice depends on the energy available at the plant, its price and the company’s emission reduction targets.

Frequently asked questions

Does the e-RTO remove VOCs as efficiently as a burner-fired RTO?+

Yes. In both cases efficiency exceeds 99%, because the oxidation process and the beds are the same.

When does an e-RTO use almost no electricity for heating?+

When the VOC concentration is above the autothermal point. The heat then comes from the pollutants themselves and the heating elements are off.

Can an existing RTO be converted to electric?+

Sometimes. It depends on the chamber design, the space for the heating elements and the power available at the plant.

W

AUTHOR

WIZZUM engineering team

We design and commission wastewater and gas treatment installations for industry, from benchmarking and FEED engineering to start-up.

NEED HELP?

Are you considering an e-RTO instead of a burner-fired RTO?

  • Comparative technical analyses
  • Design and delivery of turnkey installations
  • Environmental benchmarking and BAT analysis

Environmental engineering for industry.
Industrial wastewater, emissions and odors.

OFFICE

Avda. Cabrera, 36
08302 Mataró (Barcelona), Spain
info@wizzum.com

© 2026 Wizzum. All rights reserved.