Home / Blog / Industrial wastewater

INDUSTRIAL WASTEWATER

Food industry: how to treat wastewater with fats and high COD

Slaughterhouses, dairies, canneries and beverage makers: how fats are separated, how high COD is brought down and which treatment sequence usually works.

W
WIZZUM engineering teamPublished on 09/12/2025 · 6 min read

CONTENTS

IN SHORT

  • Food industry wastewater is almost entirely biodegradable, but the load is so high that, untreated, the discharge does not meet the conditions or the charges shoot up.
  • The proven sequence is: screen and equalization, DAF flotation, biological treatment and, if needed, polishing.
  • With COD above around 3,000 mg/l, an anaerobic stage usually pays off, because it produces biogas.

Food industry wastewater has a very recognizable profile: lots of organic matter, fats and oils, suspended solids and flow rates that change with shifts and cleaning. Almost all of it is biodegradable, and that is the good news. The bad news is that the load can be so high that, untreated, the discharge breaches the contract conditions or the discharge charges shoot up.

One profile, many variants

  • Slaughterhouses and meat processing: blood, fats, proteins and suspended solids.
  • Dairies: lactose, proteins and fats, with acid and alkaline cleaning.
  • Vegetable processing and canneries: suspended solids, starch and sometimes brines.
  • Beverages and juices: dissolved sugars, high COD and little fat.
  • Oils and snacks: large amounts of fats and oils.

In all of them, CIP cleaning causes pH and detergent peaks that have to be dampened.

The sequence that usually works

1. Screen and equalization

The screen removes coarse solids, and the equalization tank evens out flow, pH and load over the day. It is cheap and protects everything downstream.

2. Dissolved air flotation (DAF)

Fats and fine solids float better than they settle. In the DAF unit, the water is mixed with air microbubbles that lift fats and flocs to the surface, where a scraper removes them. With coagulant and flocculant, part of the COD bound to suspended solids is also removed.

123

1 Flotation chamber 2 Scraper 3 Saturator

Water saturated with air under pressure releases microbubbles that lift fats and solids to the surface.
  • Oils and fats: 80–95% removal
  • Suspended solids: 85–95%
  • COD: 50–75%, the part bound to solids
  • Flow rates from 5 to 4,000 m³/h
  • Flotation sludge more concentrated than clarifier sludge

3. Biological treatment

Dissolved COD (sugars, lactose, soluble proteins) is removed by microorganisms. There are two routes:

  • Aerobic: activated sludge, moving bed (MBBR) or MBR. They deliver the final discharge quality.
  • Anaerobic: sludge blanket or high-rate reactors, for very high COD. They remove a large part of the load with very low energy use and produce usable biogas. They are usually followed by an aerobic polishing stage.

With COD of several thousand mg/l and enough flow, the anaerobic stage gives the best economic result. With moderate loads, an aerobic-only system is simpler. We compare aerobic systems in the article “MBR or conventional biological treatment”.

4. Polishing and reuse

If the water has to go back to cleaning or auxiliary uses, an MBR or ultrafiltration with reverse osmosis provides good-quality water. In the food industry, the permitted uses of reclaimed water are limited by health regulations and have to be studied case by case.

Common problems

Fats reaching the biological stage. They form foam, float in the clarifier and foul MBR membranes. A properly sized DAF is the best protection.

Cleaning peaks. Caustic soda, acids and disinfectants can inhibit the bacteria. Equalization and neutralization are essential.

Nutrients. Some wastewaters, such as those from beverages, have high COD and little nitrogen and phosphorus, and these have to be added for the biological stage.

Odors. Water with a high organic load ferments quickly. Covered tanks and air extraction may be needed.

Sludge. The DAF and the biological stage produce a fair amount of sludge. Dewatering it in a filter press greatly reduces disposal costs.

Where to start

The first step is to characterize the water over several days, with flow measurements and analyses at different times, including during cleaning: total and soluble COD, BOD₅, suspended solids, oils and fats, nitrogen, phosphorus, pH and temperature. With that data you can decide whether a DAF is enough to comply, whether a biological stage is needed and whether the anaerobic stage will pay for itself with the biogas.

Anaerobic: UASB or EGSB

From around 3,000 mg/l of COD, an anaerobic stage usually pays off. There are two common solutions:

UASBEGSB
Organic load5–10 kg COD/m³·d10–25 kg COD/m³·d
Retention time6–12 h2–6 h
Upflow velocity0.5–1 m/h3–10 m/h
Suitable waterMedium and high load; tolerates some solidsHigh load and few solids

The EGSB takes up less space and accepts a higher load, but needs water with few suspended solids, which makes the upstream flotation more important.

Example of a complete system

At a cheese factory with a flow rate of 20 m³/h and COD of 6,000 mg/l, a line with a plate separator, DAF with coagulant and polymer, MBR and UV disinfection can reduce COD by more than 96%, to around 150 mg/l, with BOD₅ below 10 mg/l and suspended solids below 5 mg/l. At a snack factory, with starch and oil, a line of DAF, MBR, reverse osmosis and partial evaporation makes it possible to reuse around 75% of the water and send the oil and starch to biogas production.

Frequently asked questions

Is a DAF enough to treat food industry wastewater?+

Sometimes yes, if the problem is mainly fats and suspended solids. If dissolved COD is what exceeds the limit, a biological stage is needed.

When does an anaerobic stage pay off?+

Usually from around 3,000 mg/l of COD and with enough flow. It reduces energy use and produces biogas.

Can treated water be reused at a food plant?+

Yes, for cleaning or auxiliary uses, but the permitted uses are limited by health regulations and have to be set case by case.

W

AUTHOR

WIZZUM engineering team

We design and commission wastewater and gas treatment installations for industry, from benchmarking and FEED engineering to start-up.

NEED HELP?

Is the COD of your food industry wastewater too high?

  • Comparative technical analyses
  • Design and delivery of turnkey installations
  • Environmental benchmarking and BAT analysis

Environmental engineering for industry.
Industrial wastewater, emissions and odors.

OFFICE

Avda. Cabrera, 36
08302 Mataró (Barcelona), Spain
info@wizzum.com

© 2026 Wizzum. All rights reserved.