Home / Blog / Industrial wastewater

INDUSTRIAL WASTEWATER

What to do when an industrial discharge does not meet the limits

Knowing which parameter is exceeded, why and when is half the solution. Steps to correct an industrial discharge and technologies by type of pollutant.

W
WIZZUM engineering teamPublished on 05/11/2024 · 7 min read

CONTENTS

IN SHORT

  • Before buying a unit, find out which parameter exceeds the limit, for what reason and at what times.
  • Often it is enough to separate a concentrated stream or add an equalization tank, instead of expanding the whole treatment plant.
  • A jar test with a representative sample shows which reagents work and what water quality can be achieved.

An analysis above the limit, a notice from the water utility or a discharge penalty usually arrive with some urgency. It is tempting to buy the first unit you are offered. It is better to answer three questions first: which parameter is exceeded, why and when. With those answers, the solution is usually smaller and cheaper than it seems.

Step 1: which parameter is exceeded

The discharge permit or the sewer discharge contract includes many parameters, but breaches tend to concentrate on a few. Each one points to a different type of treatment:

Parameter exceededUsual originTreatment to consider
pHAcid or alkaline baths, cleaningNeutralization
Total suspended solidsRinses, processes with fine particlesCoagulation, flocculation and settling, or DAF
Oils and fatsFood industry, machining, workshopsDissolved air flotation (DAF)
COD and BOD₅Dissolved organic matterBiological treatment or MBR
Metals (Cr, Ni, Cu, Zn…)Surface treatmentChemical precipitation and separation
Conductivity and saltsRegenerations, brines, osmosis concentrateMembranes or evaporation
Color, toxic and poorly biodegradable compoundsChemicals, textiles, pharmaceuticalsAdvanced oxidation or adsorption

Step 2: why and when

Wastewater is rarely out of spec all the time. Breaches usually occur at specific moments: when a spent bath is emptied, during weekend cleaning, at a product changeover. That is why it is worth:

  • Measuring the flow and taking 24-hour composite samples over several days, not just a single grab sample.
  • Mapping the streams: which process discharges what, and when.
  • Separating the problem streams. A few liters of a concentrated bath can ruin the water for the whole plant. Treating it separately or handing it over as waste is usually cheaper than sizing the whole treatment plant for it.
  • Installing an equalization tank, which smooths out peaks and lets the treatment plant work with more stable water.

Step 3: choosing the treatment

Physico-chemical treatment

This is the basis of most industrial treatment plants. The pH is adjusted, a coagulant is added to destabilize the fine particles (0.001 to 1 mm), and a flocculant binds them into flocs. If there are metals, chemical precipitation turns them into solids. Those solids then have to be separated from the water. More details in the physico-chemical treatment datasheet.

1234

1 Coagulation 2 Flocculation 3 Lamella clarifier 4 Reagent dosing

Neutralization, coagulation and flocculation, separation in a lamella clarifier or a flotation unit, and polishing.

Dissolved air flotation (DAF)

When the water contains oils, fats or light flocs, flotation separates them better than settling. Water saturated with air under pressure is introduced, and the microbubbles lift the particles to the surface, where a scraper removes them. More information in the DAF flotation datasheet.

  • Flow rates from 5 to 4,000 m³/h
  • Typical efficiency: oils and fats, 80–95%; suspended solids, 85–95%; COD, 50–75%
  • Separation takes minutes, and the unit takes up less space than a clarifier
  • Flotation sludge is more concentrated and easier to dewater

When the problem is what is dissolved

If dissolved organic matter is what exceeds the limit, physico-chemical treatment is not enough and biological treatment or an MBR is needed. If it is salts, no conventional method removes them: you have to turn to reverse osmosis or vacuum evaporation. With very difficult water, evaporation even makes it possible to stop discharging altogether and reuse the water.

Laboratory test before buying

With a representative sample, coagulation and flocculation tests (jar tests) can be carried out to check which reagents work, at what dose and what water quality they give. It is cheap and avoids surprises at commissioning.

The sludge

Every physico-chemical treatment produces sludge. Its quantity and management are part of the cost. A filter press can reduce it to a cake with 30–40% dry solids, which greatly lowers transport and disposal costs.

What to require in a treatment plant quote

To compare quotes from different suppliers, they should all answer the same questions:

  • Input data: average and maximum flow rate, and the water analysis the design is based on.
  • Guaranteed outlet quality, parameter by parameter, and under what conditions.
  • Reagent consumption per cubic meter of treated water.
  • Amount of sludge: mass, dry solids content and how it is managed.
  • Energy use and installed power.
  • Space required and civil works.
  • Degree of automation and operator hours per day.
  • Commissioning and training, including a performance test.

A quote that does not say what water it was designed for gives no way of knowing whether the installation will meet the limits.

Design data worth knowing

ParameterIndicative value
Equalization tankAt least 4–6 h of inlet flow
Rapid mixing (coagulation)800–1,200 s⁻¹ for 30–60 s
Slow mixing (flocculation)20–80 s⁻¹ for 15–30 min
Ferric chloride dose50–200 mg/l
Polyelectrolyte dose1–5 mg/l
Settling velocity0.5–1 m/h; up to 3 m/h in a lamella clarifier
DAF hydraulic loading5–15 m³/m²·h
Sludge quantity1–2% of the treated water volume, around 3–6 kg/m³
Energy consumptionCoagulation, 0.05–0.15 kWh/m³; DAF, 0.2–0.6 kWh/m³

Two pollutants need their own stage before physico-chemical treatment. Hexavalent chromium is reduced to trivalent chromium at pH 2–3 with ferrous sulfate or metabisulfite, at a redox potential of around +250 mV; the pH is then raised to 8–9 and the chromium precipitated. Cyanides are oxidized to cyanates with hypochlorite at pH 10–11 and a redox potential of 600–650 mV; the high pH prevents hydrogen cyanide from being released. In both cases, the process is controlled continuously with pH and redox probes.

Frequently asked questions

Do you always have to build a new treatment plant?+

No. Often it is enough to separate a concentrated stream, add an equalization tank or improve reagent dosing at the existing installation.

How does a DAF differ from a clarifier?+

The flotation unit lifts the pollutants to the surface with air microbubbles. It works better with oils, fats and light flocs, and takes up less space.

Does physico-chemical treatment remove salts?+

No. Dissolved salts are removed with reverse osmosis or vacuum evaporation.

W

AUTHOR

WIZZUM engineering team

We design and commission wastewater and gas treatment installations for industry, from benchmarking and FEED engineering to start-up.

NEED HELP?

Is your discharge exceeding the limits?

  • Comparative technical analyses
  • Design and delivery of turnkey installations
  • Environmental benchmarking and BAT analysis

Environmental engineering for industry.
Industrial wastewater, emissions and odors.

OFFICE

Avda. Cabrera, 36
08302 Mataró (Barcelona), Spain
info@wizzum.com

© 2026 Wizzum. All rights reserved.