Home / Blog / Odors

ODORS

Hydrogen sulfide (H₂S): how to remove it from air and biogas

Alkaline or oxidizing scrubber, biotrickling filter, biofilter or adsorbents. How hydrogen sulfide is removed from extracted air and biogas, and when each option makes sense.

W
WIZZUM engineering teamPublished on 15/04/2025 · 5 min read

CONTENTS

IN SHORT

  • H₂S in extracted air is an odor and safety problem; in biogas, it is a matter of engine corrosion and SO₂ emissions.
  • For air, the most common options are an alkaline or oxidizing scrubber or a biotrickling filter; the dry filter is used for small flow rates and as polishing.
  • For biogas, biological desulfurization predominates, with adsorbents as a polishing stage.

Hydrogen sulfide (H₂S) is a gas that smells of rotten eggs. It can be detected at very low concentrations, it is toxic at higher concentrations and it also corrodes metals and concrete. It occurs at wastewater treatment plants, waste treatment plants, paper mills, the food and chemical industries, and in biogas. Removing it from extracted air and removing it from biogas are two different problems, with different solutions.

H₂S in extracted air

Here the aim is to prevent odor and protect people and installations. H₂S is usually accompanied by other sulfur compounds and sometimes by ammonia.

Alkaline scrubber

A packed column irrigated with a sodium hydroxide solution. H₂S, a weak acid, reacts with the caustic soda and stays in the solution. With good pH control and solution renewal governed by conductivity, efficiency exceeds 99%. It is a compact unit that responds well to peaks. See the alkaline scrubber datasheet.

Oxidizing scrubber

Scrubbing with sodium hypochlorite oxidizes H₂S and also organic sulfides, such as dimethyl sulfide, which alkaline scrubbing captures less well. Under optimal conditions, efficiency exceeds 99%. The pH and redox potential are controlled automatically, which limits reagent consumption and prevents scaling. More information in the oxidizing scrubber datasheet.

1234

1 Mist eliminator 2 Packing 3 Tank with recirculation pump 4 NaOH dosing

Packed column scrubbed countercurrent, with automatic reagent dosing.

If there is ammonia or amines in the air, they have to be removed first in an acid scrubbing stage. If they reach the hypochlorite, they form chloramines, which also smell and are irritating.

Biotrickling filter and biofilter

Sulfur bacteria oxidize H₂S to sulfate. The biotrickling filter, with plastic packing and recirculated water with pH control, treats high concentrations in a small footprint and with no chemicals. The biofilter is cheaper to run, but takes up more space and works best at low concentrations; with a lot of H₂S, a chemical scrubbing stage ahead of it is advisable.

Dry filter

For small flow rates or as a polishing stage, a bed of impregnated activated carbon or chemical adsorbent retains H₂S with an efficiency of over 99%. The adsorbent changes color when saturated, and is then replaced. Its cost limits it to small flow rates and loads. See the dry filter datasheet.

SituationOption worth considering
Medium or large flow rate, high H₂S, peaksAlkaline or oxidizing scrubber
H₂S with organic sulfidesOxidizing scrubber
No chemicals, little spaceBiotrickling
Low concentration, space availableBiofilter
Small flow rate or polishingDry filter

H₂S in biogas

In biogas, H₂S is not an odor problem but a problem for using the gas. It damages engines, boilers and pipes, and produces SO₂ when burned. Manufacturers of CHP engines and biomethane upgrading plants require a very low H₂S content. In addition, biogas is a combustible gas with no oxygen, which limits the possible technologies.

Biological desulfurization

A bioscrubber or an adapted biotrickling filter scrubs the biogas with a solution in which bacteria oxidize the sulfides. It is the most widely used option for medium and large flow rates, because of its low operating cost. It needs controlled dosing of air or oxygen for the bacteria, well away from explosive mixtures.

Chemical scrubbing

Scrubbing with caustic soda reliably removes H₂S, but it also absorbs part of the CO₂ in the biogas, which increases reagent consumption. It is used when very high removal is needed or as a polishing stage.

Adsorbents

Impregnated activated carbon or metal oxides retain the H₂S left after the main desulfurization and protect the engine or the upgrading membrane. This is the typical polishing stage.

Siloxanes

Biogas from wastewater treatment plants and landfills usually also contains siloxanes, which leave silica deposits in engines. They are removed with specific adsorbents after the gas has been dried, usually in the same polishing line.

What needs to be measured

  • The H₂S concentration, with its peaks and how it varies over the day
  • Other sulfur compounds: mercaptans, dimethyl sulfide
  • Ammonia and amines, if an oxidizing scrubber is planned
  • The flow rate, temperature and humidity
  • For biogas, also: CH₄, CO₂, O₂ and siloxanes

With this data, the main technology and, if needed, the polishing stage are chosen. We discuss odors at wastewater treatment and composting plants in more depth in the article on odors and their treatment.

Frequently asked questions

Can H₂S be removed without chemicals?+

Yes, biologically: in a biotrickling filter or a biofilter, where sulfur bacteria oxidize H₂S to sulfate.

Why is ammonia removed before the oxidizing scrubber?+

Because ammonia reacts with hypochlorite and forms chloramines, which smell and are irritating.

How is H₂S removed from biogas?+

Most commonly by biological treatment in a bioscrubber; any remaining traces are captured by impregnated carbon or metal oxide adsorbents.

W

AUTHOR

WIZZUM engineering team

We design and commission wastewater and gas treatment installations for industry, from benchmarking and FEED engineering to start-up.

NEED HELP?

Do you have a hydrogen sulfide problem in air or biogas?

  • Comparative technical analyses
  • Design and delivery of turnkey installations
  • Environmental benchmarking and BAT analysis

Environmental engineering for industry.
Industrial wastewater, emissions and odors.

OFFICE

Avda. Cabrera, 36
08302 Mataró (Barcelona), Spain
info@wizzum.com

© 2026 Wizzum. All rights reserved.